You record your setup in the Setup section of the session editor. It has three parts: chassis, tires and engine. Every field is optional, so fill in only what you changed or measured.
Before you start: pick a track
Chassis setup, Tires setup and Engine setup stay greyed out until the session has a track. You also can't save the session without one: the ✓ stays disabled. Tap Track in the Session section and pick a track. If you have no tracks yet, Track opens a form to add your first one.
The note under the Session section reminds you. It says "A track is required to save the session and enable lap times and setup details." If you have no tracks yet, it says "Add a track…" instead.
Record your setup
- Open a new session or edit an existing one.
- Under Setup, tap Chassis setup, Tires setup or Engine setup.
- Enter your values.
- Tap the X at the top right to go back to the session. Your values stay in the session.
- Tap the ✓ at the top right of the session editor to save.
If you tap the X at the top left of the session editor with unsaved changes, the app asks Discard changes?. Tap Discard changes to throw them away, or Cancel to keep editing.
What you can record
Chassis
- Axle: Soft, Medium or Hard.
- Width: Front and Rear.
- Height: Front and Rear, each Low, Mid or High.
- Camber, Caster and Toe: Left and Right. Camber and toe can be negative. Caster is free text.
- Weight distribution: turn on Front / Rear or Left / Right, then drag the slider. It starts at 50 / 50 %.
- Weight: Kart, Driver and Measured total.
Tires
- Compound.
- Pressure cold, Pressure hot and Temperature for each corner: Front left, Front right, Rear left, Rear right.
Engine
- Driver sprocket, Rear sprocket and Max. RPM.
- Tuning: Plug, Main jet, Idle / pilot jet, Needle clip (1–5), Mixture screw and Fuel/Oil.
How the gear ratio is worked out
When you have entered both sprockets, Gear ratio appears under them. It is the rear sprocket teeth divided by the driver sprocket teeth, to three decimals. For example, 84 ÷ 12 = 7.000.
Measured total and Calculated total
Measured total is the weight you read on the scales. It starts at 0. A grey Calculated total row appears below it while it is 0 and both Kart and Driver are above 0. That row shows Kart + Driver. Once you enter a measured total, the calculated row goes away and your measured value is used.
Suggested and auto-filled values
Previously used values. Compound, Plug, Main jet, Idle / pilot jet and Fuel/Oil get a clock button next to the field once you have used values before. Tap it to pick one of your last 8 different values. Values from sessions with the same kart come first. For the engine fields, values from the same engine come first, then values from the same kart.
Copy the previous setup. When Auto-fill previous setup is on, a new session gets the setup from your most recent session at the same track, on or before the session date. Kartnote looks for the same kart first, then the same class, then any session at that track. If you change the track, kart, class or date, it fills the setup again, but only if you haven't changed any setup values yet. To stop this, go to Settings and switch off Auto-fill previous setup under Session setup.
Kart and driver weights. Every new session takes Kart and Driver from the Weight on your kart and driver profile, if they are above 0. This happens even when Auto-fill previous setup is off. Measured total is never copied and starts at 0, so Calculated total shows until you enter your scale reading.
Previously used values and copying the previous setup work during the trial and with Full Access. When the app is read-only they are off, and the setting shows a lock. See Kartnote Full Access.
See your setup after saving
Open the session. Below the lap times you see Chassis, Tires and Engine sections. They show only what you recorded. The total weight row says Measured total or Calculated total, depending on which one applies. The same sections also appear when you open a single lap.